27 ISA Extension Naming Conventions

27.1 Case Sensitivity

The ISA naming strings are case insensitive.

27.2 Base Integer ISA

RISC-V ISA strings begin with either RV32I, RV32E, RV64I, or RV128I indicating the supported address space size in bits for the base integer ISA.

27.3 Instruction-Set Extension Names

Standard ISA extensions are given a name consisting of a single letter. For example, the first four standard extensions to the integer bases are: “M” for integer multiplication and division, “A” for atomic memory instructions, “F” for single-precision floating-point instructions, and “D” for double-precision floating-point instructions. Any RISC-V instruction-set variant can be succinctly described by concatenating the base integer prefix with the names of the included extensions, e.g., “RV64IMAFD”.

We have also defined an abbreviation “G” to represent the “IMAFDZicsr_Zifencei” base and extensions, as this is intended to represent our standard general-purpose ISA.

Standard extensions to the RISC-V ISA are given other reserved letters, e.g., “Q” for quad-precision floating-point, or “C” for the 16-bit compressed instruction format.

Some ISA extensions depend on the presence of other extensions, e.g., “D” depends on “F” and “F” depends on “Zicsr”. These dependences may be implicit in the ISA name: for example, RV32IF is equivalent to RV32IFZicsr, and RV32ID is equivalent to RV32IFD and RV32IFDZicsr.

27.4 Version Numbers

Recognizing that instruction sets may expand or alter over time, we encode extension version numbers following the extension name. Version numbers are divided into major and minor version numbers, separated by a “p”. If the minor version is “0”, then “p0” can be omitted from the version string. Changes in major version numbers imply a loss of backwards compatibility, whereas changes in only the minor version number must be backwards-compatible. For example, the original 64-bit standard ISA defined in release 1.0 of this manual can be written in full as “RV64I1p0M1p0A1p0F1p0D1p0”, more concisely as “RV64I1M1A1F1D1”.

We introduced the version numbering scheme with the second release. Hence, we define the default version of a standard extension to be the version present at that time, e.g., “RV32I” is equivalent to “RV32I2”.

27.5 Underscores

Underscores “_” may be used to separate ISA extensions to improve readability and to provide disambiguation, e.g., “RV32I2_M2_A2”.

Because the “P” extension for Packed SIMD can be confused for the decimal point in a version number, it must be preceded by an underscore if it follows a number. For example, “rv32i2p2” means version 2.2 of RV32I, whereas “rv32i2_p2” means version 2.0 of RV32I with version 2.0 of the P extension.

27.6 Additional Standard Extension Names

Standard extensions can also be named using a single “Z” followed by an alphabetical name and an optional version number. For example, “Zifencei” names the instruction-fetch fence extension described in Chapter [chap:zifencei]; “Zifencei2” and “Zifencei2p0” name version 2.0 of same.

The first letter following the “Z” conventionally indicates the most closely related alphabetical extension category, IMAFDQCVH. For the “Zam” extension for misaligned atomics, for example, the letter “a” indicates the extension is related to the “A” standard extension. If multiple “Z” extensions are named, they should be ordered first by category, then alphabetically within a category—for example, “Zicsr_Zifencei_Zam”.

Extensions with the “Z” prefix must be separated from other multi-letter extensions by an underscore, e.g., “RV32IMACZicsr_Zifencei”.

27.7 Supervisor-level Instruction-Set Extensions

Standard supervisor-level instruction-set extensions are defined in Volume II, but are named using “S” as a prefix, followed by an alphabetical name and an optional version number. Supervisor-level extensions must be separated from other multi-letter extensions by an underscore.

Standard supervisor-level extensions should be listed after standard unprivileged extensions. If multiple supervisor-level extensions are listed, they should be ordered alphabetically.

27.8 Machine-level Instruction-Set Extensions

Standard machine-level instruction-set extensions are prefixed with the three letters “Zxm”.

Standard machine-level extensions should be listed after standard lesser-privileged extensions. If multiple machine-level extensions are listed, they should be ordered alphabetically.

27.9 Non-Standard Extension Names

Non-standard extensions are named using a single “X” followed by an alphabetical name and an optional version number. For example, “Xhwacha” names the Hwacha vector-fetch ISA extension; “Xhwacha2” and “Xhwacha2p0” name version 2.0 of same.

Non-standard extensions must be listed after all standard extensions. They must be separated from other multi-letter extensions by an underscore. For example, an ISA with non-standard extensions Argle and Bargle may be named “RV64IZifencei_Xargle_Xbargle”.

If multiple non-standard extensions are listed, they should be ordered alphabetically.

27.10 Subset Naming Convention

Table 1.1 summarizes the standardized extension names.